®
DX9000 Series
Video Storage Unit
Installation/
Operation Manual
C684M-A (7/01)
U
®
L
LISTED
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120 • DataFAX +1(559) 292-0435
PelcoEurope BV • Dillenburg Center, Dillenburgstraat 7C • 5652 AM Eindhoven • The Netherlands
Tel +31(40) 251-9870 • FAX +31(40) 251-9835
CONNECTIONS
One, two, three, or four video storage units can be connected to a recorder, depending on
the requirements of your system.
Refer to Figure 2 to install the storage units.
1. Connect the appropriate end of the SCSI cable to the SCSI connector on each video
storage unit.
2. Read the Caution Notice in the Mounting section. Connect the other end of the
SCSI cable from each video storage unit to the SCSI connector in slot 1 of the re-
corder. Connect the first storage unit (labeled 01) to the upper left connector. Connect
the second storage unit (labeled 02) to the upper right connector. Connect the third
storage unit (labeled 03) to the lower left connector. Connect the fourth storage unit
(labeled 04) to the lower right connector.
3. Select the appropriate power cord (USA or European standard) and plug it into the
power receptacle on the back of each video storage unit. Plug the other end into a
power supply, preferably through an uninterruptible power supply.
4. Turn on the power switch on the back of one of the video storage units. Then open the
front door with the supplied key. Press the square button to turn on the power. Close
the door. The LEDs on the front of the unit light to show the hard drives are working.
NOTE: All video storage units
connected to a recorder must
be turned on before turning
on the recorder.
5. Repeat step 4 for each storage unit.
6. Turn on the power switch on the back of the recorder. Then open the front door with
the supplied key. Press the square button to turn on the power. Close the door.
7. Go to the System Configuration section of the Installation/Operation Manual for the
Digital Video Recorder to continue with the installation procedure.
RECORDER
STORAGE UNIT #1
*
STORAGE UNIT #2
*
STORAGE UNIT #3
*
STORAGE UNIT #4
*
** STORAGE UNITS ARE NUMBERED AND MUST BE CONNECTED TO THE PROPER CONNECTOR.
00850
Figure 2. Connection Storage Units to Recorder
Pelco Manual C684M-A (7/01)
3
SPECIFICATIONS
ELECTRICAL/VIDEO
Input Voltage:
Power Consumption:
Recording Resolution
NTSC:
100-240 VAC, 50/60 Hz, auto-ranging
250W maximum
352 x 240 pixels
384 x 288 pixels
MPEG1
PAL:
Compression:
Compressed Image Size: 352 x 240; average 1.4 kB
Remote Control:
Full remote control via TCP/IP network
MECHANICAL
SCSI Connector:
Recorder interface
GENERAL
Operating Temperature:
Relative Humidity:
Dimensions
41° to 104°F (5° to 40°C)
Maximum 80% non-condensing
Desktop:
Rack Mount:
Unit weight:
7.3 (H) x 17.0 (W) x 19.6 (D) inches (18.5 x 43.2 x 49.8 cm)
7.0 (H) x 19.0 (W) x 19.6 (D) inches (17.8 x 48.3 x 49.8 cm)
45 lb (20.4 kg) maximum (fully equipped)
(Design and product specifications subject to change without notice.)
REGULATORY NOTICES
This equipment has been tested and found to comply with the limits of a Class A digital de-
vice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial envi-
ronment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his
own expense.
WARRANTY AND RETURN INFORMATION
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100
or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide
the following information:
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective
in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
Five years on Pelco manufactured cameras (CC3500/CC3600 and MC3500/
MC3600 Series); two years on all other cameras.
•
•
•
Three years on Genex™ Series (multiplexers, server, and keyboard).
Two years on all standard motorized and fixed focal length lenses.
Two years on Legacy®, Camclosure™ Camera Systems, CM6700/CM6800/
CM8500/CM9500/CM9740/CM9750/CM9760 Matrix, DF5 Series and DF8
Fixed Dome products.
If there is a dispute regarding the warranty of a product which does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.
Method of return shipment shall be the same or equal to the method by which
the item was received by Pelco.
•
Two years on Spectra® and Esprit™, including when used in continuous mo-
tion applications.
Two years on WW5700 series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders.
Six months on all pan and tilts, scanners or preset lenses used in continu-
ous motion applications (that is, preset scan, tour and auto scan modes).
RETURNS
•
•
•
In order to expedite parts returned to the factory for repair or credit, please call
the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number
(CA number if returned for credit, and RA number if returned for repair). Goods
returned for repair or credit should be clearly identified with the assigned CA/RA
number and freight should be prepaid. All merchandise returned for credit may
be subject to a 20% restocking and refurbishing charge.
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s li-
ability for any claim, whether based on breach of contract, negligence, infringe-
ment of any rights of any party or product liability, relating to the Products shall
not exceed the price paid by the Dealer to Pelco for such Products. In no event
will Pelco be liable for any special, incidental or consequential damages (includ-
ing loss of use, loss of profit and claims of third parties) however caused, whether
by the negligence of Pelco or otherwise.
Ship freight prepaid to: Pelco
3500 Pelco Way
Clovis, CA 93612-5699
The above warranty provides the Dealer with specific legal rights. The Dealer
may also have additional rights, which are subject to variation from state to state.
REVISION HISTORY
Manual # Date
Comments
C684M
4/01
7/01
Original version.
C684M-A
Revised Description, Installation, and Connections sections. Added FCC notice.
® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco.
™ Esprit and Camclosure are trademarks of Pelco.
© Copyright 2001, Pelco
All rights reserved.
4
Pelco Manual C684M-A (7/01)
|