Pelco Network Card C2241M User Manual

I N S T A L L A T I O N  
ID-P Pendant Mount  
Adapter  
C2241M (12/09)  
 
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Only use attachments/accessories specified by the manufacturer.  
6. Installation should be done only by qualified personnel and conform to all local codes.  
7. Use only installation methods and materials capable of supporting four times the maximum  
specified load.  
8. Only use replacement parts recommended by Pelco.  
9. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is  
designed for indoor use only and it must not be installed where exposed to rain and moisture.  
4
C2241M (12/09)  
 
 
Description  
The ID-P is a pendant mount adapter specifically designed for ID and IDE Series network dome cameras.  
The pendant adapter modifies the network dome camera for pendant installations using a  
1.5-inch (3.81 cm) NPT mount, such as the SWM-WT mount.  
PARTS LIST  
Qty Description  
1
1
1
ID-P pendant mount adapter  
Tube of Loctite®  
Installation manual  
Installation tools, mounting hardware, and the following parts are needed but not supplied:  
Qty Description  
1
1
1
1
ID or IDE Series network dome camera  
1.5-inch (3.81 cm) NPT mount, such as the SWM-WT mount  
Lens (use either a megapixel or standard auto iris lens, depending on camera model)  
IX-SC service cable  
C2241M (12/09)  
 
5
   
Installation  
1. Install the 1.5-inch (3.81 cm) NPT mount; refer to the instructions supplied with the mount.  
2. Pull the system power and video wiring through the mount.  
3. Route the wiring through the ID-P pendant mount adapter. Apply Loctite (supplied) to the threads of  
the ID-P, and then screw the pendant mount adapter onto the mount.  
Figure 1. Installing the Pendant Mount Adapter  
4. Install the lens on the ID or IDE Series camera module:  
NOTE: Megapixel lenses are designed and tested to deliver optimal image quality to megapixel  
cameras. A standard definition lens installed on a megapixel camera will limit the resolution of the  
camera and create poor image quality.  
a.  
b.  
Remove the cover from the lens mount.  
Screw the lens onto the lens mount. Be careful to prevent dust from entering the space  
between the lens and the imager. If necessary, use clean, compressed air to remove any  
foreign matter (refer to the instructions shipped with the lens).  
c.  
Connect the auto iris lens to the 4-pin connector located on the side of the camera. Refer to  
Figure 2 for pin designation and iris drive connector information.  
3
4
Pin DC (AID) Auto Iris Lens  
1
2
3
4
Control coil negative (–)  
Control coil positive (+)  
Drive coil positive (+)  
Drive coil negative (–)  
1
2
Figure 2. Lens Pin Connections  
6
C2241M (12/09)  
 
   
5. Connect the network cable to the RJ-45 network port. If the network has no Power over Ethernet  
(PoE), connect a 24 VAC Class 2 power supply to the 24 VAC power connector.  
1
8
Pin  
1
Function  
TX+  
8
7
6
5
4
3
2
1
8
1
2
TX–  
1
2
3
4
5
6
7
8
3
RX+  
4
PoE 1-2  
PoE 1-2  
RX–  
5
1
2
3
4
5
6
8
7
7
8
6
6
5
4
3
2
1
7
PoE 3-4  
PoE 3-4  
8
Figure 3. RJ-45 Pin Descriptions  
6. Connect the alarm and relay connector:  
a.  
Connect the alarm and relay wires to the supplied 4-pin connector.  
b.  
Attach the mating connector to the green connector on the side of the camera.  
Figure 4. Alarm and Relay Connector  
C2241M (12/09)  
7
 
7. If PoE is not available, connect the VAC connector:  
a.  
Connect the 24 VAC wires to the supplied 2-pin VAC connector.  
b.  
Attach the mating connector to the green connector on the side of the camera.  
24V~  
Figure 5. 24 VAC Connector  
NOTE: If you are operating the camera using 24 VAC and you are wiring more than one camera to the  
same transformer, connect one side of the transformer to the red wire (24 VAC +) and connect the  
other side of the transformer to the black wire (24 VAC –). Failure to connect all modules identically  
might introduce video noise for some installations.  
8. Install the camera module in the pendant mount adapter:  
a.  
Compress the spring clips and push the camera module until it locks into place.  
b.  
Tighten the machine screws completely to secure the camera module to the adapter.  
Figure 6. Installing the Camera Module  
8
C2241M (12/09)  
 
9. Apply power to the camera. The camera will complete a configuration sequence: the green LED  
flashes five times per second for approximately two minutes and then turns solid after the sequence  
is complete.  
NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) server and  
DHCP is enabled, the configuration sequence might take up to five minutes to complete.  
10. To complete the installation, refer to the ID Series Installation/Operation manual or the IDE Series  
Installation/Operation manual.  
C2241M (12/09)  
 
9
Specifications  
MECHANICAL  
Mounting Method  
Attach the ID-P to a mount with 1.5-inch (3.81 cm) NPT pipe (such  
as the SWM-WT mount)  
GENERAL  
Construction  
Finish  
Aluminum  
Polyester powder coat  
1.69 lb (0.77 kg)  
Unit Weight  
(Design and product specifications subject to change without notice.)  
0.54  
(1.37)  
7.50  
(19.05)  
5.12  
(13.00)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE IN INCHES.  
The materials used in the manufacture of this document and its components are compliant to the requirements of  
Directive 2002/95/EC.  
REVISION HISTORY  
Manual #  
Date  
Comments  
C2241M  
12/09  
Original version.  
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.  
Spectra III is a trademark of Pelco, Inc.  
DLP is a registered trademark of Texas Instruments Incorporated.  
All product names and services identified throughout this document are trademarks or registered trademarks of their respective companies.  
The absence of a trademark or registered trademark from this document does not constitute a waiver of intellectual property rights.  
© Copyright 2009, Pelco, Inc. All rights reserved.  
10  
C2241M (12/09)  
 
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment.  
Exceptions to this warranty are as noted below:  
Five years:  
Fiber optic products  
Unshielded Twisted Pair (UTP) transmission products  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models  
Three years:  
Pelco-designed fixed network cameras and network dome cameras with Sarixtechnology.  
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, and IP3701H Series)  
EH1500 Series enclosures  
Spectra® IV products (including Spectra IV IP)  
Camclosure® Series (IS, ICS, IP) integrated camera systems  
DX Series digital video recorders, DVR5100 Series digital video recorders, Digital Sentry® Series hardware products, DVX Series digital video  
recorders, and NVR300 Series network video recorders  
Endura® Series distributed network-based video products  
Genex® Series products (multiplexers, server, and keyboard)  
PMCL200/300/400 Series LCD monitors  
Two years:  
Standard varifocal, fixed focal, and motorized zoom lenses.  
DF5/DF8 Series fixed dome products  
Legacy® Series integrated positioning systems  
Spectra III, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.  
Esprit Ti and TI2500 Series thermal imaging products  
Esprit and WW5700 Series window wiper (excluding wiper blades).  
CM6700/CM6800/CM9700 Series matrix  
Digital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days.  
The air filter is not covered under warranty.  
Intelli-M® eIDC controllers  
PMCL542F, PMCL547F, and PMCL552F FHD monitors  
One year:  
Video cassette recorders (VCRs), except video heads. Video heads will be covered for a period of six months.  
Six months:  
All pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under  
this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelcos  
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products  
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or consequential  
damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state  
to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if  
returned for credit, and RA number if returned for repair) and designated return location.  
All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid  
10-19-09  
 
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA  
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150  
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120  
 

Philips Baby Accessories SC280 User Manual
Philips Blu ray Player BDP3010 F7 User Manual
Philips Computer Monitor 105E19 User Manual
Philips Model Vehicle AT751 User Manual
Pioneer Car Satellite TV System SC 1525 K User Manual
Pioneer DVD Player DVH P5650MP User Manual
Polycom Server 623128UK User Manual
Porter Cable Cordless Drill 90550130 User Manual
PYLE Audio Headphones PLVWH1 User Manual
PYLE Audio Home Theater Server PLTV65R User Manual