SUB-Woofer
Control
ADJ
ILL
IN S TR UC TION M AN UAL
P WM - 3 0 M
6 BAND PARAMETRIC EQUALIZER
INTRODUCTION
FEATURES:
6 BAND PARAMETRIC EQUALIZER WITH 4 CHANNEL OUTPUT
IN-DASH DIN SIZE: EASY COMPOUND WITH OTHER HEAD-UNIT TO A 2-DIN
SIZE SYSTEM
MOTORIZED HIDDEN ADJUST BUTTONS
X-BREATH DUAL-COLOR INTELLECTIVE ILLUMINATION
FRONT/REAR SEPARATE EQUALIZER ADJUSTMENT
FRONT/REAR SEPARATE GAIN ADJUSTMENT
SUB-WOOFER PRE-OUT & CONTROLLER (FREQ. & GAIN)
AUTOMATIC POWER SWITCH
GOLD PLATED INPUT / OUTPUT SOCKETS
BALANCED HIGH / LOW LEVEL INPUT
NIGHT ILLUMINATION
-1-
INSTALLATION
The following illustration shows a typical installation. However, you should
make adjustments corresponding to your specific car. If you have any
questions or require information regarding installation kits, consult your car
audio dealer or a company supplying kits.
In-dash single mounting
1
Screws(M5x10mm)
Screws(M5x10mm)
Dashboard
Bracket
Frame
Lock nut
(M5)
Mounting bolt
Stay
Bracket
Compound with other head-unit to a 2-din size system
2
Screws(M5x6mm)
Bracket
Screws(M5x6mm)
Bracket
Frame
-2-
ELECTRONIC CONNECTIONS
Typical Connections
1
To the positive terminal of the car battery
(bypassing the ignition switch)
To metallic body or
chassis of the car
3A fuse
Yellow
Black
LINE IN FRONT REAR
SUB
OUTPUT
INPUT
LEVEL
GROUND ISOLATION
L
L
ISOLATED
220
Ω
GROUND
7V
0.7V
R
R
Left Right
Line in
RCA
High Level Input
Yellow
Left +
Left -
Low level Input
Yellow/Black
Orange
Left
Right +
Line out
(Front)
Orange/Black
Right
Left
Right -
Line out
(Rear)
Right
Left
Violet
Remote On
Sub-
Woofer
out
Right
Red
To the car ignition switch
controlled power wire
(Accessory terminal)
Connection to your CD/Cassette player
2
Connect this unit's Remote On lead to your head player's remote lead if any
(such as auto antenna lead), so this unit's power can be controlled through
the head player. If there is no suitable lead from your audio source
equipment, connect to the car ignition switch controlled power wire
(Accessory terminal).
1
Note: For some models of head players, the auto antenna lead only works in
radio receiving mode.
-3-
ELECTRONIC CONNECTIONS
If your head player provides
If your head player does not provide RCA
type line out, then disconnect the head
player's speaker leads, connect them to
this unit's High Level Input leads.
2
RCA type line out, connect
them to this unit's Line In
socket.
Line in
EQ
Line in
EQ
High Level Input
speake rs
if any
CD/Casset te
player
CD/Casset te
player
Line out
Note: Do not use this unit's low level and high level input together.
Adjust the INPUT LEVEL to meet your source unit's
3
output level. Turn clockwise when your head player has a
normal level output; turn counter-clockwise if your head
player has high level preamp output.
Occasionally alternator noise may appear because the
4
source unit and amplifier may use different grounding. To
help in this situation, you may select the GROUND
ISOLATION switch to a proper position.
Connection to Subwoofer and externa l amplifier
3
Front spe ake rs
Amplifier
Line in
Rear spe ake rs
Subwoofer
Amplifier
Line in
Note: No low-pass filter is required for the subwoofer amplifier.
-4-
LOCATION OF THE BUTTONS
4
3
F1-L F2-L F3-L
F4
R4
R1-L R2-L R3-L
POWER
ON
FRONT
REAR
SLEEP
dB -15
LEVEL
+15
30-150
-15
+15
-15
+15
Min
Max
Min
Max
-15
+15
30-150
-15
+15
-15
+15 dB
LEVEL
3K-15K
GAIN
LEVEL
GAIN
300-1.5K
3K-15K
300-1.5K
FREQ
Hz
Hz
Low
Hi
Low
Hi
Low
Hi
Low
Hi
Low
Hi
Low
Hi
FREQ
MIN
MAX
30Hz
180
FREQ
SUB-Woofer
Control
ADJ
ILL
P WM-3 0 M
P a r a e t r ic Eq u a liz e r
m
F1-F
F2-F F3-F
S2 S1 S3
R1-F R2-F R3-F
1
5
2
SUB-Woofer Control
Button
S-1
S-2
Front Band 1 Level Adjust Button
Front Band 2 Level Adjust Button
Front Band 3 Level Adjust Button
Front Band 1 Frequence Adjust Button
F1-L
F2-L
F3-L
F1-F
Subwoofer Level Adjust
Button
S-3 Subwoofer Frequence
F2-F Front Band 2 Frequence Adjust Button
Adjust Button
F3-F Front Band 3 Frequence Adjust Button
F4
Front Gain Adjust Button
1
Adjust Buttons Position
Switch
R1-L Rear Band 1 Level Adjust Button
2
3
4
5
Illumination Switch
Power Indicator
Sleep Indicator
Subwoofer On/Off
Switch
R2-L Rear Band 2 Level Adjust Button
R3-L
R1-F
R2-F
R3-F
R4
Rear Band 3 Level Adjust Button
Rear Band 1 Frequence Adjust Button
Rear Band 2 Frequence Adjust Button
Rear Band 3 Frequence Adjust Button
Rear Gain Adjust Button
-5-
Oper at ions
4
3
F1-L F2-L F3-L
R1-L R2-L R3-L
POWER
ON
FRONT
REAR
SLEEP
dB -15
LEVEL
+15
30-150
-15
+15
-15
+15
Min
Max
Min
Max
-15
+15
30-150
-15
+15
-15
+15 dB
LEVEL
3K-15K
GAIN
LEVEL
GAIN
FREQ
300-1.5K
3K-15K
300-1.5K
Hz
Hz
Low
Hi
Low
Hi
Low
Hi
Low
Hi
Low
Hi
Low
Hi
FREQ
MIN
MAX
30Hz
180
FREQ
SUB-Woofer
Control
ADJ
ILL
P WM-3 0 M
P a r a e t r ic Eq u a liz e r
m
F1-F
F2-F F3-F
R1-F R2-F R3-F
1
2
Turn On/Off the unit
1
2
When you connect the Remote On lead, the unit will be turned
automatically on/off following the audio source equipment.
Adjust Buttons Position Switch
Press the 1 (Adjust Buttons Position Switch) button, the Adjust buttons
move forward for further adjustment. Press the 1 (Adjust Buttons Position
Switch) button again, the Adjust buttons move back to the normal position
to prevent accidental adjustment.
When the unit turned off, the Adjust buttons move back to the normal
position automatically.
Illumination Switch
3
The unit is in Power On Status:
Press the 2 (Illumination Switch) button, the illumination modes change
as follows:
X-Breath mode(Dual color)
Blue color mode
Red color mode
-6-
Oper at ions
The unit is in Power Off Status:
Press the 2 (Illumination Switch) button, you can turn off the X-breath
illumination.
Power Indicator
4
5
When the unit turned on, the 3 (power indicator) indicator lights up.
Front Equalizer Level & Frequence Adjustment
Adjust F1 -L, F2 -L, F3 -L buttons to change the equalizer level of each
band.
Adjust F1 -F, F2 -F, F3 -F buttons to change the equalizer center
frequence of each band.
g(dB)
g(dB)
15
12
9
6
3
(Hz )
f
(Hz )
f
0
f1
f2
0
-3
-6
-9
-12
-15
LEVEL ADJUST CURVE
CENTER FREQUENCE ADJUSTCURVE
Rear Equalizer Level & Frequence Adjustment
6
Adjust R1 -L, R2 -L, R3 -L buttons to change the equalizer level of each
band.
Adjust R1 -F, R2 -F, R3 -F buttons to change the equalizer center
frequence of each band.
-7-
Oper at ions
F4
R4
POWER
ON
FRONT
REAR
SLEEP
dB -15
LEVEL
+15
30-150
-15
+15
-15
+15
Min
Max
Min
Max
-15
+15
30-150
-15
+15
-15
+15 dB
LEVEL
3K-15K
GAIN
LEVEL
GAIN
300-1.5K
3K-15K
300-1.5K
FREQ
Hz
Hz
Low
Hi
Low
Hi
Low
Hi
Low
Hi
Low
Hi
Low
Hi
FREQ
MIN
MAX
30Hz
180
FREQ
SUB-Woofer
Control
ADJ
ILL
P WM-3 0 M
P a r a e t r ic Eq u a liz e r
m
S2 S1 S3
(Front Channel) Gain Control
7
8
9
Adjusting F4 (Front Gain Adjust) button can change the front channel
amplifier gain level to fit your system input and output level demand.
(Rear Channel) Gain Control
Adjusting R4 (Rear Gain Adjust) button can change the rear channel
amplifier gain level to fit your system input and output level demand.
SUB-woofer Control
Press the S 1 (SUB-woofer Control) button to turn on /off the SUB-
woofer output.
Adjust the S 2 (SUB-woofer Level) button to change the SUB-woofer
gain level
Adjust the S 2 (SUB-woofer Level) button to change the SUB-woofer
cut-off frequence.
-8-
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following
points before calling a service center.
Indication
Symptoms
Causes
Remedies
Power Sleep
LED LED
Illumination
The unit dose
not works at Off
No power Check the fuse and
Off
Off
wiring to the battery.
supplied
all.
Check the connection
and the +12volts
power of REM.On.
Slowly Blue Sleep
Off
On
Off
Glow
mode
No sound
On
Off
Incorrect Check your fro nt &
from the
speaker
gain
setting
re ar gain sett ings.
Check your sourc es
volume, input cord .
On
Off
Off
No input
-9-
SPECIFICATIONS
AUDIO SECTION
100dB
0.01%
S/N Ratio (Rated Power, 1KHz)
Distortion
100dB
Separation (Rated Power, 1KHz)
FREQ. Response (1KHz= 0dB, + /-2dB)
RCA Input Level
10Hz-35KHz
0.7-7V
20KΩ
RCA Input Impedance
HI-Level Input Level
5V
100Ω
HI-Level Input Impedance
Gain
20dB
7V
Line Out Level (RMS.)
Line Out Impedance
1KΩ
6V
SUB-WOOFER Output Level
SUB-WOOFER Output Cut-off FREQ.
EQ Control Range
30Hz - 180Hz
+ /- 15dB
GENERAL SECTION
9V-15V
NEGATIVE GROUND
1A
Power Source
Ground System
MAX Current
1.25Kg
Weight
178x50x180mm
Dimensions (W x H x D)
Design and specifications subject to change without notice.
|