S3.15
Multi-Hip Option
Assembly Instructions
S3.15 Multi-Hip Option Assembly Instructions
Table of Contents
Important Safety Instructions....................................................................... 2
Personal Safety During Assembly ........................................................................................... 2
Obtaining Service .................................................................................................................... 2
BeforeYou Begin ........................................................................................... 4
Unpacking the Equipment ....................................................................................................... 4
1
2
Preparations................................................................................................... 5
Required Tools......................................................................................................................... 5
Installation Requirements ........................................................................................................ 5
Assembly Tips ......................................................................................................................... 5
Assembly Instructions .................................................................................. 6
1. Attach the Multi-Hip to the S3.15 .................................................................................. 7
2. Assemble the Multi-Hip ................................................................................................. 8
3. Install the Multi-Hip Cable ............................................................................................. 9
4. Attach the Multi-Hip Cable to the S3.15 ........................................................................ 10
3
4
Warranty ......................................................................................................... 11
Limited Warranty Statement .................................................................................................... 11
Warranty Registration Card ..................................................................................................... 13
Specifications ............................................................................................................. Back cover
Table of Contents
page 3
S3.15 Multi-Hip Option Assembly Instructions
1
Before You Begin
Thank you for purchasing the Multi-Hip Option. This
option will add a new dimension to your strength-
training regimen. For proper installation, please read
this guide thoroughly and follow the assembly
instructions.
S3.15
Unpacking the Equipment
The Multi-Hip Option is carefully tested and inspected
before shipment. Precor Strength ships the unit in
several pieces that require assembly. Ask for
assistance during the assembly process.
Multi-Hip Option
•
•
Review the Installation Requirements.
Carefully unpack the pieces and lay them on the
floor near the location where you plan to use the
equipment.
If any items are missing, contact the dealer from whom
you purchased the unit. For more information, refer to
Obtaining Service.
Before You Begin
page 4
S3.15 Multi-Hip Option Assembly Instructions
Installation Requirements
•
Most fasteners are ³⁄₈ inch unless otherwise noted.
To find out the length of a particular fastener,
measure its shank (the long, narrow part beneath
the head). Refer to the following diagram:
Follow these installation requirements when
assembling the unit:
•
•
Fill out and mail the warranty registration card.
Set up the Multi-Hip Option on a solid, flat surface.
A smooth, flat surface under the unit helps keep
it level.
Fastener head
2
Preparations
You must review and follow the instructions in this
guide. If you do not assemble and use the Multi-Hip
Option according to the following guidelines, you could
void the Precor Limited Warranty.
•
•
Provide ample space around the machine.
Open space around the machine allows for easier
access.
To determine the
length of a fastener,
measure its shank.
Fastener threads
Shank
Insert all fasteners in the same direction. For
aesthetic purposes, insert all the fasteners in the
same direction unless specified (in text or
illustrations) to do otherwise.
Required Tools
Tools that you need to obtain before assembling the
unit include:
•
•
Zinc fasteners are used with the titanium parts.
Black fasteners are used when assembling the
stone gray painted surfaces.
•
Leave room for adjustments. Tighten fasteners
(such as screws, nuts, and bolts), so the unit is
stable, but leaves room for adjustments. Do not
fully tighten fasteners until instructed (in the steps)
to do so.
❏
❏
❏
❏
❏
❏
❏
⁹⁄₁₆-inch socket
³⁄₄-inch socket
Most fasteners are fitted to the frame or pulley, you
will need to disassemble the fasteners before
proceeding with each step. Some pieces have
extra holes that you will not use. Use only those
holes indicated in the instructions and illustrations.
⁹⁄₁₆-inch box-end wrench
³⁄₄-inch box-end wrench
Crescent wrench
Assembly Tips
•
Fasteners may become loose and fall off during
Wire tie cutter (cuts plastic tie wraps)
Utility knife
•
•
Read all caution notes on each page before
completing that step.
shipment. Inspect the plastic wrap and packaging
for loose parts. To alleviate confusion during
assembly, reattach the loose fasteners and pulleys
found in the packaging.
While you may be able to assemble the Multi-Hip
Option by reading the illustrations only, refer to the
text for important safety cautions and notes.
•
A black 6-inch scale with white numbers is
provided at the bottom of every assembly
instruction page. Use this scale to identify the
correct fastener size. The head of a fastener is not
used in measuring the length.
Preparations
page 5
S3.15 Multi-Hip Option Assembly Instructions
Assembly
Instructions
3
Assembly of the Multi-Hip Option takes professional
installers about ¹⁄₂ hour to complete. If this is the first
time you have assembled this type of equipment, plan
on significantly more time.
Selector Hub
Professional installers are highly recommended!
However, if you acquire the appropriate tools, obtain
assistance, and follow the assembly steps sequentially,
the process will take time, but is fairly easy.
Roller pad
CAUTION: Obtain assistance! Do not attempt to
assemble the Multi-Hip Option by yourself. Review
the Installation Requirements before proceeding
with the following steps.
With so many assembled parts, proper alignment and
adjustment is critical. While tightening the fasteners, be
sure to leave room for adjustments. Do not fully tighten
fasteners until instructed to do so.
Important: Be careful to assemble components in the
sequence presented in this manual.
Crossbrace
1
2
3
4
5
6
Assembly Instructions
page 6
S3.15 Multi-Hip Option Assembly Instructions
1. Attach the Multi-Hip to
the S3.15
Important: Most fasteners are fitted to the frame
or pulley, you will need to disassemble the
fasteners before proceeding with each step.
2 - 2¹⁄₄" bolts
A. Attach the Multi-Hip Base to the S3.15 Rear
Crossbar using
2 - washers
B
three 1¼-inch hex head bolts
three flat washers
three spring washers
three locknuts
B. Position the Crossbrace against the S3.15 Main
Base and place it on top of the Multi-Hip flange.
Attach the Crossbrace to the Multi-Hip using
two 2¹⁄₄-inch hex head bolts
two flat washers
Crossbrace
Multi-Hip Flange
C. Attach the Crossbrace to the S3.15 Main Base
Rear
Crossbar
using
two 4¹⁄₄-inch hex head bolts
four radius washers
two locknuts
Multi-Hip
Upright
Note: If you plan to install the S3.15 Leg Press
Option immediately after you complete the Multi-
Hip Option assembly, place two washers and two
locknuts on the fastener ends finger tight so they
provide stability, but can easily be removed.
Spring
Washer
3 - 1¼" bolts
3 - flat washers
3 - spring washers
3 - locknuts
Main Base
A
2 - 4¹⁄₄" bolts
4 - radius washers
2 - locknuts
C
1
2
3
4
5
6
Step 1. Attach the Multi-Hip to the S3.15
page 7
S3.15 Multi-Hip Option Assembly Instructions
2. Assemble the Multi-Hip
Important: The orientation of the Handlebar fasteners,
the Roller Arm, and the Selector Stem is critical for the
proper alignment of the Selector Hub. Assemble the
parts with the orientation shown in the illustration.
Selector Hub
2 - 2½" bolts
4 - washers
2 - locknuts
A
C
Selector Stem
Roller Arm
A. Attach the Handlebar to the Multi-Hip using
two 2½-inch hex head bolts
four flat washers
1 - ³⁄₄" zinc
buttonhead bolt
1 - washer
two locknuts.
Roller Pad
B. Attach the Roller Arm to the Selector Stem using
one ³⁄₄-inch zinc buttonhead bolt
one zinc washer
C. Install the Selector Hub assembly to the Multi-Hip
Upright using
1 - ³⁄₄" zinc
buttonhead bolt
1 - washer
B
one ³⁄₄-inch zinc buttonhead bolt
one zinc washer
Multi-Hip
Upright
D. Wrench tighten all fasteners.
1
2
3
4
5
6
Step 2. Assemble the Multi-Hip
page 8
S3.15 Multi-Hip Option Assembly Instructions
3. Install the Multi-Hip Cable
Pulley assemblies
A. Feed the tab end of the Multi-Hip Cable 130194
3½-inch Pulley (used on gray
painted parts)
between the two 3½-inch pulleys on the Multi-Hip
Upright and attach the cable to the Selector Hub
using
one shaft
two e-clips
1 - bolt
2 - shoulder spacers
1 - locknut
Selector Hub
B. Remove the lower 3¹⁄₂-inch pulley on the Multi-Hip
Upright. Feed the cable around it and reattach it
using
1 - shaft
2 - e-clips
A
3½-inch Pulley (used on
titanium parts)
one 4-inch hex head bolt
two shoulder spacers
one locknut
1 - zinc bolt
2 - zinc washers
1 - zinc locknut
C. Remove the 3¹⁄₂-inch pulley from its pulley bracket.
Feed the cable around it and reattach it using
one 2¼-inch hex head bolt
Multi-Hip
Upright
two flat washers
one locknut
D. Wrench tighten all pulley fasteners.
1 - 2¼" bolt
2 - washers
1 - locknut
C
1 - 4" bolt
2 - 1" shoulder spacers
1 - locknut
B
1
2
3
4
5
6
Step 3. Install the Multi-Hip Cable
page 9
S3.15 Multi-Hip Option Assembly Instructions
4. Attach the Multi-Hip Cable to
the S3.15
A. Attach the end of the Multi-Hip Cable to the S3.15
Cable using
one 1-inch hex head bolt
one locknut
B. Wrench tighten the locknut, but do not bend the
flanges.
C. Position the Pivoting Bracket to align the cables.
If necessary, loosen the fastener securing the
Pivoting Bracket to the Main Base. Retighten the
fastener after aligning the cables.
This completes the assembly of the Multi-Hip Option.
Before using the Multi-Hip, check the cable tension
throughout the S3.15 unit. Refer to Cable Adjustments
and Maintenance in the S3.15 Assembly and
Maintenance Guide.
C
1 - 1" bolt
1 - locknut
A
B
1
2
3
4
5
6
Step 4. Attach the Multi-Hip Cable to the S3.15
page 10
Precor Residential Equipment Limited Warranty
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING
YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE
CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.
3. Warranty of all Precor products applies to residential use only and is void when products are
used in a nonresidential environment or installed in a country other than where sold.
4. Except in Canada, Precor does not pay labor outside the United States.
5. Warranties outside the United States and Canada may vary. Please contact your local Dealer
for details.
Limited Warranty.
Precor Incorporated warrants all new Precor products to be free from defects in materials and
manufacture for the warranty period set forth below. The warranty period commences on the
invoice date of original purchase. This warranty applies only against defects discovered within
the warranty period and extends only to the original purchaser of the product. Parts repaired or
replaced under the terms of this warranty will be warranted for the remainder of the original
warranty period only. To make claim under warranty, the buyer must notify Precor or their
authorized Precor dealer within 30 days after the date of discovery of any nonconformity and
make the affected product available for inspection by Precor or its service representative.
Precor’s obligations under this warranty are limited and set forth below.
This limited warranty shall not apply to:
1. Software version upgrades
2. Cosmetic items, including, but not limited to the following: grips, seats, and labels.
3. Repairs performed on Precor equipment missing a serial number or with a serial tag that has
been altered or defaced.
4. Service calls to correct installation of the equipment or instruct owners on how to use the
equipment.
5. Pickup, delivery, or freight charges involved with repairs.
6. Any labor costs incurred beyond the applicable labor warranty period.
Warranty Periods and Coverage
All residential products and commercial products used in the home are warranted for the
following periods:
Disclaimer and Release
The warranties provided herein are the exclusive warranties given by Precor and supersede any prior,
contrary or additional representations, whether oral or written. ANY IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED ABOVE
ARE LIMITED IN DURATIONTO THE PERIODS OF EXPRESS WARRANTIES GIVEN ABOVE FOR THOSE SAME PARTS.PRECOR
HEREBY DISCLAIMS AND EXCLUDESTHOSE WARRANTIES THEREAFTER. Some states do not allow limitation on how
long an implied warranty lasts, so the above limitation may not apply to you. PRECOR ALSO HEREBY DISCLAIMS
AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH
RESPECT TO ANY NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED TO: (A) ANY OBLIGATION,
LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS
SUPPLIERS (WHETHER ACTIVE, PASSIVE OR IMPUTED);AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM, OR REMEDY FOR
LOSS OF OR DAMAGE TO ANY EQUIPMENT. This disclaimer and release shall apply even if the express warranty set
forth above fails of its essential purpose.
•
•
•
•
Lifetime frame and welds
10 years parts and wear items
1 year labor
Coverage for options and accessories defined below.
Options / Accessories
Many options or accessories have components that are connected internally or mounted inside the
electronic console.The following guidelines determine the warranty for these components. If the
internal components are installed by the factory or by an authorized dealer as part of the original
sale and delivery, they have a warranty that is identical to the warranty of the equipment in which
they are connected or mounted. If the internal components are not installed by the factory or by an
authorized dealer as part of the original sale and delivery, they have a 90-day parts and labor
limited warranty. All components that are not internally connected have 90-day parts only limited
warranty. Satisfactory proof of purchase is required in all cases.
Exclusive Remedies
For any product described above that fails to conform to its warranty, Precor will provide, at their option, one of
the following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty service
may be obtained by contacting the authorized dealer from whom you purchased the item. Precor
compensates Servicers for warranty trips within their normal service area to repair equipment at the owner’s
location. You may be charged a trip charge outside the service area. THESE SHALL BE THE SOLE AND EXCLUSIVE
REMEDIES OFTHE BUYER FOR ANY BREACH OFWARRANTY.
Conditions and Restrictions
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the Precor product only while:
a. It remains in the possession of the original purchaser and proof of purchase is
demonstrated
Exclusion of Consequential and Incidental Damages
b. It has not been subjected to accident, misuse, abuse, improper service, or non-Precor
modifications
c. Claims are made within the warranty period
PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY, WHETHER ARISING IN CONTRACT
(INCLUDING WARRANTY), TORT (INCLUDING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR
OTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE, REVENUE OR PROFIT, COST OF
CAPITAL, COST OF SUBSTITUTE EQUIPMENT, ADDITIONAL COST INCURRED BY BUYER (BY WAY OF CORRECTION OR
OTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT. This exclusion
applies even if the above warranty fails of its essential purpose and regardless of whether such damages
are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other
legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation might not apply.
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in
compliance with electrical codes or Precor owner’s manual specifications, or failure to provide
reasonable and necessary maintenance as outlined in the owner’s manual.
Complete this portion and keep for your records.
Purchased From: ____________________________ Example: Dealer or store name.
Phone Number: _____________________________ Example: Dealer or store telephone number.
Product/model: _____________________________ Example: M9.31
This warranty gives you specific legal rights, and you may also have other rights, which vary state
to state.
Effective 01 January 2003
Serial number:______________________________ The serial number is found on the shipping container
P/N 36287-110
page 11
Please detach and mail in the warranty registration within ten days of purchase.
S3.15 Multi-Hip Option Specifications
Length: 32 inches (81 cm)
Height: 46 inches (115 cm)
Width: 30 inches (75 cm)
Shipping weight: 51 lb (23 kg)
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
Precor is a registered trademark of Precor Incorporated.
Specifications subject to change without notice.
Copyright 2006 Precor Incorporated.
S3.15 Multi-Hip Option Literature Kit 49452-101
S3.15 Multi-Hip Option Assembly Instructions 49453-101
Warranty Registration 45623-102
NOTICE:
Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. and foreign patents for
both the mechanical construction and the visual aspects of its product design. Any party contemplating the use of Precor’s product designs is hereby
forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor will vigorously pursue all
unauthorized appropriation of its proprietary rights.
Warranty Card # 36287-110
15 September 2006
|